Gas Entrainment and Inclusions in the Die Casting Filling (Part Two)
- https://www.die-casting-company.com/gas-entrainment-and-inclusions-in-the-die-casting-filling-part-two.html
- Junying Die Casting Company
How to avoid gas entrainment and inclusions？ We know that gas entrainment and oxidation inclusions can be formed in the die casting...
- 4 Years, 2 Months ago
- 32 views
- Technical Articles
Gas Entrainment and Inclusions in the Die Casting Filling (Part One)
- https://www.die-casting-company.com/gas-entrainment-and-inclusions-in-the-die-casting-filling-part-one.html
- Junying Die Casting Company
As a near-net forming technology, die casting is widely used in industries such as automobiles, aerospace and communications due to its high production efficiency...
- 4 Years, 2 Months ago
- 40 views
- Technical Articles
Industrialization of the Composite 3D Printing for General Motors
- https://www.die-casting-company.com/industrialization-of-the-composite-3d-printing-for-general-motors.html
- Junying Die Casting Company
A few days ago, General Motors Corporation (GM) announced the opening of a 15,000 square feet Additive Industrialization Center (AIC) in the Warren Technology...
- 4 Years, 3 Months ago
- 9 views
- Technical Articles
Development of Aluminum Alloy Die Castings for Automobile Steering Knuckles (Part Two)
- https://www.die-casting-company.com/development-of-aluminum-alloy-die-castings-for-automobile-steering-knuckles-part-two.html
- Junying Die Casting Company
4. Trial production results and analysis of steering knuckle castings 4.1 The influence of extrusion force on the internal quality of castings Figure 6 shows the...
- 4 Years, 4 Months ago
- 24 views
- Technical Articles
Die Casting Technologies of Automobile Structural Parts (Part Three)
- https://www.die-casting-company.com/die-casting-technologies-of-automobile-structural-parts-part-three.html
- Junying Die Casting Company
3.6 The vacuum process Vacuum filling is an important process measure for die casting of automobile structural parts. The following aspects should be paid attention...
- 4 Years, 4 Months ago
- 50 views
- Technical Articles
The Die Casting Technology of Automobile Structural Parts (Part Two)
- https://www.die-casting-company.com/the-die-casting-technology-of-automobile-structural-parts-part-two.html
- Junying Die Casting Company
3.3 Alloy melting and processing For general use, Silafont-36 and Castasil-37 alloys can be used in die casting production without special treatments. However,...
- 4 Years, 5 Months ago
- 60 views
- Technical Articles
Development of Aluminum Alloy Die Castings for Automobile Steering Knuckles (Part One)
- https://www.die-casting-company.com/development-of-aluminum-alloy-die-castings-for-automobile-steering-knuckles-part-one.html
- Junying Die Casting Company
Abstract: The extrusion die casting process was adopted to develop the 400MPa automotive steering knuckle die casting. Aluminum alloy steering knuckle die castings with...
- 4 Years, 5 Months ago
- 70 views
- Technical Articles
Eliminating Heat Cracks of Aluminum Die Castings by Optimizing the Cooling Control
- https://www.die-casting-company.com/eliminating-heat-cracks-of-aluminum-die-castings-by-optimizing-the-cooling-control.html
- Junying Die Casting Company
The cost of producing die castings is high, and in extreme cases, die castings with defects can lead to malfunctions. Shorter and shorter development cycles increase...
- 4 Years, 6 Months ago
- 66 views
- Technical Articles
The Die Casting Technology of Automobile Structural Parts (Part One)
- https://www.die-casting-company.com/the-die-casting-technology-of-automobile-structural-parts-part-one.html
- Junying Die Casting Company
Introduction Due to high performance and quality requirements, most automobile structural parts are made of iron or steel materials and produced through...
- 4 Years, 6 Months ago
- 184 views
- Technical Articles
Porsche and GM Have Obtained Achievement in 3D Printing Auto Parts Technology
- https://www.die-casting-company.com/porsche-and-gm-have-obtained-achievement-in-3d-printing-auto-parts-technology.html
- Junying Die Casting Company
Porsche just announced that it would return to Le Mans with a surprising new prototype, and we can't wait to know its price. Although motorsport...
- 4 Years, 4 Months ago
- 33 views
- Technical Articles